Flooring Solutions

  • weberfloor DPM

    weberfloor DPM is a highly moisture tolerant, epoxy resin damp proof system, especially designed to bond to concrete surfaces even when the concrete is still drying out and containing a high degree of moisture.

  • weberfloor 4716

    weberfloor 4716 primer is a styrene acrylate dispersion which can be diluted with water and is intended for use with Weber’s flooring products.

    weberfloor 4716 does not contain ammonia. It offers good alkali resistance and adhesion properties in both wet and dry environments.

  • weber.floor 4655 industry flow rapid

    weber.floor 4655 industry flow rapid is a cement-based pumpable selflevelling screed for use as a surface layer on industrial flooring applications.

    It is supplied as a pre-blended, dry powder for application of a thickness of between 4 – 15 mm.

  • weber.floor 4610 industry top

    weber.floor 4610 industry top is a pumpable, rapid hardening, self-levelling screed for use as a surface layer on industrial flooring.

    The material is especially suitable where renovation time is limited. weber.floor 4610 is ready for normal traffic loading without further finishing, but may be coated with a suitable resin should this be required.

  • weber.floor flex

    weber.floor flex is a high-performance, fibre-modified, cement-based, self-smoothing, self-levelling, rapid-setting floor screed with low dust technology.

  • monoprufe wp elastic

    Monoprufe WP Elastic

    Monoprufe WP Elastic is used in swimming pools, tanks and basements to contain or exclude water and can accommodate some structural movement within the substrate.

    Supplied as a two component material, Monoprufe WP Elastic is a blend of polymers, cements, graded fillers and chemical binders. The two components are simply mixed on site to form a highly workable coating, which is roller applied to the prepared substrate. It is to be covered with a screed or render; it is not capable of resisting wear or abrasion.

  • Monoprufe DPM

    Monoprufe DPM

    Monoprufe DPM is applied before laying thin bonded screeds or proprietary levelling compounds onto suitable substrates.

    By suppressing residual moisture in concrete floors the addition of Monoprufe DPM permits the early installation of moisture sensitive floor finishes and thin bonded or standard unbonded screeds even when the relative humidity of the base concrete is in excess of 75%.

  • ronafix prepacked tanking render with GL

    Ronafix Pre-packed Tanking Render

    When cured,  Ronafix Pre-packed Tanking Render bonds monolithically to concrete and other surfaces and will resist both positive and negative pressure.

    Ronafix Pre-packed Tanking Render is used in swimming pools, tanks and basements to contain or exclude water.

    For damp proofing walls use Ronafix Pre-packed Tanking Render as a thin bonded render to resist moisture and the passage of hygroscopic salts.

    Ronafix Pre-packed Tanking Render provides improved chemical resistance and is therefore suitable for use in bunds and storage areas where chemicals are present.

  • ronafix prepacked render screed with GL

    Ronafix Pre-packed Render / Screed

    Ronafix Pre-packed Render/Screed is used for thin section, high strength, waterproof screeds.

    It is strong, durable and resistant to water and frost attack.

  • RonaFloor Epoxy Floor Mortar Rapid

    RonaFloor Epoxy Floor Mortar Rapid

    RonaFloor Epoxy Floor Mortar Rapid also provides new wearing surfaces. Its formulation allows thin section application from 5mm. It is suitable for forming coves, skirtings and upstands.

    It offers good mechanical resistance and will resist attack from most industrial chemicals including acids, alkalis, oils, fats, solvents and foodstuffs. Surfaces laid or repaired with RonaFloor Epoxy Floor Mortar can be accessed by foot traffic after only 3 hours and by heavy loads after 4 hours (at 20°C). RonaFloor Epoxy Floor Mortar has been designed for ease of use and practicality of application.

  • A CAD drawing of RonaFloor Repair 1 Hour 25mm.

    RonaFloor Repair 1 Hour 25mm

    When RonaFloor Repair 1 Hour 25mm is applied, the repaired surface can be opened to traffic after 1 hour.

    RonaFloor Repair 1 Hour 25mm+ can be used from 25mm upwards. As well as achieving rapid strength, RonaFloor Repair 1 Hour 25mm+ can be used down to a temperature of –10°C, when conventional mortars cannot be used.

  • ronafloor repair 1 hour 6-50mm with GL

    RonaFloor Repair 1 Hour 6-50mm

    RonaFloor Repair 1 Hour 6-50mm can be opened to heavy vehicular traffic after 1 hour. RonaFloor Repair 1 Hour can be used from 6-50mm.

    As well as achieving rapid strength, RonaFloor Repair 1 Hour 6-50mm can be used down to a temperature of –10°C, when conventional mortars cannot be used.

    Also use as a rapid bedding mortar for blocks, pavers and other components.