Grouting, Anchoring and Bedding

  • The official logo of Sika

    Armorex Construction Grout

    Armorex Construction Grout is a blend of selected cements, graded silica sand and compatible admixtures, which when mixed with water produces a high strength grout with good flow properties and slight expansion.

  • The official logo of BASF

    Bristar

    BRISTAR is a Non Explosive Demolition Agent.

  • Fosroc-Cebex-100

    Cebex 100

    Cebex 100 is used where a reduced water/cement ratio and positive expansion is required.

    Applications include bed grouting, duct grouting, non-shrink infilling and jointing.

  • The official logo of FOSROC

    Cebex 120

    Cebex 120 entrains a controlled quantity of small air bubbles which impart cohesion and workability to a mortar and improves its durability when set.

    These bubbles are particularly stable, improving mortar quality and assisting in keeping mix workability at satisfactory levels.

  • The official logo of FOSROC

    Cebex 250

    When added to the grout, the Cebex 250 produces a gel in the water phase which surrounds the cement particles and protects them from washout.

    Cement hydration is not impaired by the use of this admixture.

  • The official logo of FOSROC

    Cebex 311

    Cebex 311 is a chloride free, plasticising & retarding, ready to use aqueous solution based on a blend of organic compounds.

    It is used as a set retarding admixture in structural and mass concrete where a controlled extension of the concrete’s setting time is required.

  • The official logo of FOSROC

    Cebex 430

    Cebex 430 is supplied as a brown solution which instantly disperses in water.

    It disperses the fine particles in the screed mix, enabling the water content of the screed to perform more effectively.

  • The official logo of FOSROC

    Cebex 653

    Cebex 653 is designed for addition to cementitious grout mixes to enable them to be placed in moving water conditions without excessive washout of cement.

    The product is a tunnel annulus grout admixture used to produce an instantaneous gelation and fast set behind tunnel linings.

  • The official logo of FOSROC

    Cebex 705

    Cebex 705 entrains a controlled quantity of small air bubbles which impart cohesion and workability to a mortar and improve its durability when set.

    These bubbles are particularly stable, improving mortar quality and assisting in keeping mix workability at satisfactory levels.

  • The official logo of FOSROC

    Cebex Cable Grout 100

    Cebex Cable Grout 100 is supplied as a dry powder requiring only the addition of a controlled amount of clean water and cement to produce a free flowing non-shrink grout.

    The material is designed to allow uniform mixing, and eliminates unwanted segregation and bleeding.

  • The official logo of FOSROC

    Cebex Cable Grout Plus

    Cebex Cable Grout Plus is an all fines admixture containing expansive cement which impart controlled expansion in the plastic state whilst minimizing water demand.
    The material is designed to allow uniform mixing, and eliminates unwanted segregation and bleeding.

  • The official logo of FOSROC

    Conbextra AT

    Conbextra AT, with the addition of a controlled amount of clean water produces a free-flowing grout with high early and ultimate strengths as well as long term durability, suitable for use in section thicknesses 10mm to 100mm.

    Thicker sections can be achieved by incorporating clean, dry 10mm aggregate.

  • The official logo of FOSROC

    Conbextra AT+

    Conbextra AT+, with the addition of a controlled amount of clean water produces a free-flowing grout with high early and ultimate strengths as well as long term durability, suitable for use in section thicknesses 10 mm to 100 mm.

    Thicker sections can be achieved by incorporating clean, dry 10mm aggregate at a ratio of up to 1:1 depending on aggregate shape and quality.

  • The official logo of FOSROC

    Conbextra BB

    Conbextra BB has been formulated specifically for grouting of bridge bearings and parapet post baseplates.

    The dry powder is a blend of Portland cements, graded silica sands and additives to which only a controlled amount of clean water is added in situ to produce a highly flowable, non shrink grout.

  • The official logo of FOSROC

    Conbextra BB92

    High flexural strength and modulus elasticity without the addition of fibres
    Quick return to service and removal of temporary supports

    Suitable for pumping or pouring

    High fatigue resistance

    No segregation or bleeding to ensure consistent final physical performance and to prevent pump blockages

     

  • The official logo of FOSROC

    Conbextra Cable Grout

    Conbextra Cable Grout is supplied as a ready to use dry powder requiring only the addition of a controlled amount of clean water to produce a free flowing non-shrink grout.

  • Conbextra EP10

    Conbextra EP10 for grouting gap thicknesses from 0.25 to 10 mm.

    Comprising of a two component, low viscosity unfilled epoxy resin system which is mixed and poured into the gap

  • The official logo of FOSROC

    Conbextra EP10LV

    Conbextra EP10LV is designed for injecting into cracks, honeycombs and construction joints ranging from 0.25mm to 9mm.

    High mechanical strength
    Excellent adhesive strength
    Two part system
    Non shrink
    Chemical resistant

  • The official logo of FOSROC

    Conbextra EP10TG

    Conbextra EP10TG is an all liquid system consisting of base and hardener.

    Excellent durability – high strengths
    Cost effective Conbextra EP10TG
    User friendly- simple, full pack mixing
    Versatile – suitable for a wide range of loading situations
    Excellent in service performance – non-shrink

  • Fosroc-Conbextra-EP120

    Conbextra EP120

    Conbextra EP120 is supplied as a three component system consisting of base, hardener and specially graded aggregate.

    Excellent durability – high strengths
    Cost effective
    User friendly – simple full pack mixing
    Versatile – suitable for a wide range of loading situations
    Excellent in service performance – non-shrink

  • The official logo of FOSROC

    Conbextra EP300

    Conbextra EP300 three component system consisting of base resin, liquid hardener and specially graded inert fillers are supplied in the correct mix proportions designed for whole pack mixing on site and no other materials should be added.

  • The official logo of FOSROC

    Conbextra EP75

    Conbextra EP75 is designed for grouting of gap widths of 10 to 75 mm. It is supplied as a three component system consisting of base, hardener and specially graded aggregate.

    The components are supplied in the correct mix proportions designed for whole pack mixing on site.

  • The official logo of FOSROC

    Conbextra EPR

    Conbextra EPR is a three-component system consisting of base resin, liquid hardener and specially graded inert fillers.

  • Conbextra GP

    Conbextra GP is a blend of Portland cements, graded fillers and chemical additives.

    The filler grading produces a highly flowable grout which will not segregate or bleed.